How To Change Belt On Whirlpool Dryer

Download Commodity

Download Article

Here is a step past step tutorial on how to supercede a dryer belt on a Whirlpool dryer. This is a relatively unproblematic repair that tin can salve you time and money since yous won't have to call in an expensive repairman for a common problem.

Steps Download Article

1

Start past removing the lint filter. Using your five/16th screwdriver, remove the two screws under the lint filter.^[1]
2

Side by side, take the putty pocketknife and identify it in the opening between the top of the dryer and the front of the dryer. Popular upwardly the peak of the dryer and echo on the other side.^[2]

Advertisement
3

Flip the superlative out of the style. At that place will exist two screws in each upper corner of the inside of the dryer. Remove both of these and put screws in container for afterward.
four

The forepart of the dryer volition now exist released. Pull the elevation away from the cabinet and then lift information technology up. Swing the front to the side and place information technology out of the way. You may need to disconnect the chapeau switch wires if they are non long plenty to permit this.^[three]
v
Release the chugalug from around the drum. ^[iv] To practice this, the chugalug volition be looped under the idler pulley and then fastened to the motor. Reach under the drum and unhook the belt from effectually the motor.
- The pulley may be simply a spring part with a one-half circumvolve the the belt runs effectually, with no moving part.
half-dozen

To attach the new chugalug, begin by placing the belt, with the groove side downward and lined up with the markings effectually the pulsate. Then loop the belt nether the idler caster (that has a moving bike) and attach it back to the motor. The idler pulley should use tension to the belt. You may demand an actress hand for this footstep since the dryer drum can sag downward and make it hard to accomplish the motor.^[five]
vii

Make sure the rear felt on the back stop of the drum isn't folded nether. If it has, apply a screwdriver to popular the felt out while spinning the drum with your manus.
viii

Reassemble the dryer. Make sure the small tabs on the lesser of the dryer lucifer up with the small-scale holes on the dryer front. Supplant screws and lint trap.

Advertizement

Add New Question

Question

What happens if the wheel is missing from the idler caster?

Many models did non have idler wheels, simply instead just a semi-circle fabricated of metal.
Question

My "modest tabs" on the bottom of the front casing broke. Is at that place a substitute or some other way to hold it in place? It'southward all fixed but the front casing is lopsided and I'thou unsure if this will hurt it. What can I do?

The same matter happened to me. I drilled i hole on each side of that, beneath where the tabs were, and used a couple of drywall screws to concord it in place. That was several years agone and it has been working fine ever since.
Question

Where tin can I get a new dryer belt?

Apparatus stores and larger hardware stores will carry replacement belts. Take your old belt with you and they can help get you the same size. If you don't have any luck locally, you tin find a replacement chugalug for your model on Whirlpool's website, eBay or Amazon.

Enquire a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Video

When reassembling the door panel brand sure the slotted tabs on the bottom of the door panel slip onto the screws on both sides of the frame near the lesser console.
The inside of the dryer can accumulate a lot of dirt so information technology's a good idea to vacuum the within while you accept the dryer apart.
Place the belt around the pulsate starting time. Use a small tin can to prop upward the pulsate if working solitary. You will have to reach between the drum and front to remove the can before closing the front completely.
The springs tin be removed from the door to permit the front to be moved completely away.
It can be a little tricky getting the belt onto the shaft. Make certain the idler caster fits correctly into the slots.
It is best to place the dryer on its back while reattaching the front end door panel.
- Identify wooden blocks under information technology to protect the gas and electrical fittings from damage
- Marshal the dryer drum by insuring that information technology rest on the two lower wheels in back of the dryer.
- Add the front plastic guides to the front of the dryer drum.
- Carefully reattach the front end console.
- When finished, set the dryer dorsum in place reconnect the gas line and plug in the electric cord.

Thanks for submitting a tip for review!

Secure the top so it does not autumn while working on the belt/pulsate assembly.
Brand sure your dryer is unplugged and completely powered down before beginning any repair.

Things You lot'll Need

5/16th nut driver or socket
Putty knife
Container for screws
Phillips screwdriver
lightweight gloves to protect fingers when placing belt (under tension)onto motor shaft.